RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868
RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868
RAK Wireless WisDuo Breakout Board
RAK3244
overview
BastWAN is a Feather form factor board with the ultra-low power and high performance RAK4260 module at its heart. It is powered by the Microchip R34 LoRa® System-in-Package (SiP) which includes a 48Mhz SAML21 32-bit microcontroller. It also features native USB functionality and a LoRa transceiver.
Developed by Electronic Cats, the BastWAN features a micro USB port and LiPo battery charger, as well as unique elements such as an ATECC608A crypto authentication chip and 2MB of SPI flash for additional storage.
For easy software development, the Arduino environment is fully supported, including a LoRa/LoRaWAN® compatible stack.
The board comes pre-installed with the UF2 bootloader and appears as a virtual drive. Reprogramming is as easy as dragging and dropping the firmware file - no special tools are required. Since this bootloader is BOSSA compatible, it can also be used directly with Arduino's integrated development environment (IDE), MakeCode, and many other programs.
BastWAN comes fully assembled, tested and programmed with the UF2 USB bootloader.
Characteristics
Main features
- Perfect for beginners and advanced developers.
- Fast prototype with LoRa/LoRaWAN technology
- Can easily accommodate a large number of sensors and actuators with existing expansion cards.
- Open source design and firmware by Electronic Cats
LoRa Features
- Ultra-Low-Power LoRa® SiP Device
- Supports the frequency range from 862 to 1020 MHz
- Reception sensitivity up to -148 dBm
- Maximum transmission power up to 20 dBm
- Low RX current of 17 mA (typical)
- LoRa, (G)FSK, (G)MSK modulations
Product specifications
- RAK4260 @ 48MHz with 3.3V logic/power supply
- 256KB FLASH + 32KB RAM
- 32.768 kHz quartz for clock generation and RTC
- 3.3V regulator with 500mA peak current output
- Native USB support, with USB bootloader and debugging via the serial interface
- 20 IO pins available on pin headers
- PWM, Hardware Serial, Hardware I2C, Hardware SPI support
- 6 x 12-bit analog inputs
- 1 x 10-bit analog output (DAC)
- Built-in 100mA LiPo charger with charging status indicator LED
- Pin #13 red LED for general flashing purposes
- Power/Enable pin
- Reset pin and button
- 4 mounting holes
scope of delivery
- 1x BastWAN development board
- 1x antenna for LoRa
- 1x Micro USB cable
- 1x set of jumper wires
Link to data sheet
RAK3244 BastWAN | RAKwireless Documentation Center
Details about RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868
Manufacurer:
Weight:
Recommended accesories for RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868
Reviews for RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868
Your review appreciation cannot be sent
Report comment
Report sent
Your report cannot be sent
Write your review
Review sent
Your review cannot be sent
Do you have any questions about RAK Wireless · LoRa · WisDuo · Breakout Board · RAK3244EU868- Contact our experts
Benjamin M. Tanner – Managing Director and Security Expert
Do you need individual advice for your project? Do you have any questions about products, project planning or installation? As a managing director with over 18 years of experience in the field of security technology, I would be happy to help you and answer your personal concerns.
- Personal advice
- Trained Expert
- Fast Reply
- 20 years of experience